PIP VECV1001

Click here to purchase
This Practice provides requirements for use by a Purchaser for determining the design criteria for pressure vessels constructed in accordance with ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 or Division 2, henceforth referred to as the Code. Requirements that are specific to Code, Section VIII, Division 2 are shown in braces { }.

This Practice describes the requirements for the design, materials of construction, inspection and testing of pressure vessels constructed in accordance with Code, Section VIII, Division 1 {or 2}. Guidance is also provided for the development of purchase specifications for the construction of new pressure vessels which meet the philosophy and requirements of Code, Section VIII, Division 1 {or 2}.

This Practice also applies to bulk solids product containers, electric immersion process heaters, shell and plate exchangers, shell and tube exchangers, and air-cooled exchangers. See PIP VECBI001 and PIP VESBI002 for the additional requirements specific to bulk solids product containers only. See PIP VESEH001 for the additional requirements specific to electric immersion process heaters. See PIP VECSP001 and PIP VESSP002 for the additional requirements specific to shell and plate exchangers only. See PIP VECST001 and PIP VESST002 for the additional requirements specific to shell and tube exchangers only. See PIP VESAC001 for the additional requirements specific to air-cooled exchangers only.

This Practice is intended to be used for the purchase of vessels where the Manufacturer is also responsible for performing detailed design for the vessels in accordance with the Code and PIPVESV1002. If Purchaser also performs a detailed design, the design shall also be in accordance with PIP VESV1002.

The following are not covered by this Practice:
a. Standardized pre-designed (i.e., off-the-shelf) vessels (see PIP VESSM001)
b. Vessels with layered construction
c. Small vessels and low-pressure vessels (see PIP VESSM001 and PIP VESLP001)
d. Process design of trays and other removable internals

Product Details

Published:

07/01/2020

Number of Pages:

25

File Size:

1 file , 210 KB

Click here to purchase
Note to Readers: This Practice contains design criteria for pressure vessels and shell-and-tube heat exchangers. Corresponding subject matter for pressure vessels and shell-and-tube heat exchangers is covered by paragraphs identically numbered. Paragraphs pertaining to pressure vessels are preceded by [V]. Paragraphs pertaining to shell-and-tube heat exchangers are preceded by [E]. Paragraphs pertaining to both are preceded by [V/E]. In addition, ASME Boiler and Pressure Vessel Code, Section VIII, Division 2 requirements are shown in braces { }.

This Practice should be used for pressure vessels built to Division 1 or Division 2 of the ASME Boiler and Pressure Vessel Code, henceforth referred to as the Code. Shell-and-tube heat exchangers are limited to Division 1 in this Practice.

[V] The primary focus of this Practice is to communicate vessel design criteria and methodology from the User to a Designer. This Practice is also intended as guidance for the development of purchase specifications covering the construction of new pressure vessels which meet the philosophy and requirements of Section VIII, Division 1 {or 2} of the Code.

[E] The primary focus of this Practice is to communicate vessel design criteria and methodology from the User to a Designer. This Practice is also intended as guidance for the development of purchase specifications covering the construction of new shell-and-tube heat exchangers which meet the philosophy and requirements of Section VIII, Division 1 of the Code and TEMA Standards of the Tubular Exchangers Manufacturers Association.

[V/E] This Practice must be used in conjunction with PIP VEDST003, PIP VEDV1003, PIP VEFV1100, and PIP VESV1002 in order to comprise a complete vessel purchase specification.

[V/E] Many recognized and generally accepted good engineering construction practices are included herein. However, in light of the many diverse service applications of Code vessels, these practices must be employed with engineering judgment and supplemented as appropriate with requirements related to specific materials of construction, service fluids, operating environments, and vessel geometries. Accordingly, provisions of this Practice may be overridden or supplemented by an Overlay Specification.

[V/E] Standardized pre-designed (off-the-shelf) vessels and heat exchangers are not within the scope of this Practice but are covered in PIP VESSM001.

Product Details

Published:

11/01/2004

File Size:

1 file , 270 KB

Click here to purchase
This Practice provides requirements for use by a Purchaser for determining the design criteria for pressure vessels constructed in accordance with ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 or Division 2, henceforth referred to as the Code. Requirements that are specific to Code, Section VIII, Division 2 are shown in braces { }.

This Practice describes the requirements for the design, materials of construction, inspection and testing of pressure vessels constructed in accordance with Code, Section VIII, Division 1 {or 2}. Guidance is also provided for the development of purchase specifications for the construction of new pressure vessels which meet the philosophy and requirements of Code, Section VIII, Division 1 {or 2}.

This Practice also applies to bulk solids product containers, electric immersion process heaters, shell and plate exchangers, shell and tube exchangers, and air-cooled exchangers. See PIP VECBI001 and PIP VESBI002 for the additional requirements specific to bulk solids product containers only. See PIP VESEH001 for the additional requirements specific to electric immersion process heaters. See PIP VECSP001 and PIP VESSP002 for the additional requirements specific to shell and plate exchangers only. See PIP VECST001 and PIP VESST002 for the additional requirements specific to shell and tube exchangers only. See PIP VESAC001 for the additional requirements specific to air-cooled exchangers only.

This Practice is intended to be used for the purchase of vessels where the Manufacturer is also responsible for performing detailed design for the vessels in accordance with the Code and PIP VESV1002. If Purchaser also performs a detailed design, the design shall also be in accordance with PIP VESV1002.

Product Details

Published:

01/01/2019

Number of Pages:

25

File Size:

1 file , 710 KB

Click here to purchase
This Practice provides requirements for use by a Purchaser for determining the design criteria for pressure vessels constructed in accordance with ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 or Division 2, henceforth referred to as the Code. Requirements that are specific to Code, Section VIII, Division 2 are shown in braces { }.This Practice provides requirements for purchasing pressure vessels that are to be designed and fabricated by a Manufacturer.

This Practice describes the requirements for the design, materials of construction, inspection and testing of pressure vessels constructed in accordance with Code, Section VIII, Division 1 {or 2}. This Practice also provides guidance for the development of purchase specifications for the construction of new pressure vessels which meet the philosophy and requirements of Code, Section VIII, Division 1 {or 2}.

Product Details

Published:

09/01/2017

Number of Pages:

26

File Size:

1 file , 210 KB

Click here to purchase
This Practice provides vessel design criteria and methodology from the User to a Designer. This Practice is also intended as guidance for the development of purchase specifications covering the construction of new pressure vessels which meet the philosophy and requirements of Section VIII, Division 1 {or 2} of the Code.

This Practice shall be used in conjunction with PIP VEDV1003 – Vessel Drawing/Data Sheet and Instructions, PIP VEDV1003-D_EEDS – Vessel Drawing Data Sheet, PIP VEFV1100 – Vessel/S&T Heat Exchanger Standard Details, and PIP VESV1002 – Vessel Fabrication Specification ASME Code Section VIII, Divisions 1 and 2, in order to comprise a complete vessel purchase specification.

Product Details

Published:

05/01/2009

Number of Pages:

38

File Size:

1 file , 150 KB

Click here to purchase
This Practice provides requirements for use by a Purchaser for determining the design criteria for pressure vessels constructed in accordance with ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 or Division 2, henceforth referred to as the Code. Requirements that are specific to Code, Section VIII, Division 2 are shown in braces { }.This Practice provides requirements for purchasing pressure vessels that are to be designed and fabricated by a Manufacturer.

This Practice describes the requirements for the design, materials of construction, inspection and testing of pressure vessels constructed in accordance with Code, Section VIII, Division 1 {or 2}. This Practice also provides guidance for the development of purchase specifications for the construction of new pressure vessels which meet the philosophy and requirements of Code, Section VIII, Division 1 {or 2}.

Product Details

Published:

03/01/2012

Number of Pages:

28

File Size:

1 file , 310 KB

Click here to purchase
This Practice provides vessel design criteria and methodology from the User to a Designer. This Practice is also intended as guidance for the development of purchase specifications covering the construction of new pressure vessels which meet the philosophy and requirements of Section VIII, Division 1 {or 2} of the Code.

This Practice shall be used in conjunction with PIP VEDV1003 – Vessel Drawing/Data Sheet and Instructions, PIP VEDV1003-D_EEDS – Vessel Drawing Data Sheet, PIP VEFV1100 – Vessel/S&T Heat Exchanger Standard Details, and PIP VESV1002 – Vessel Fabrication Specification ASME Code Section VIII, Divisions 1 and 2, in order to comprise a complete vessel purchase specification.

Product Details

Published:

02/01/2007

File Size:

1 file , 160 KB